templatemaker.nl

A typical paper bag that can be stored completely flat. This template can be used to create both a slick little goodie bag or a large grocery bag. This design is also used a lot for gift wrapping wine bottles. The top of the bag is folded for reinforcement.

A box with lid, for example a shoe box or a board game box. Length, Width and Height are all inner dimensions.

For ease of use, Clearance is set as a percentage. The Length and Width will be scaled by this amount.

A triangle-shaped box that can be used to store pieces of cake.

The box consists of an upper and a lower part. The upper part is the cover. The lower part, the tray, does not need glue because it will be locked by the cover.

By default, the cover is 5% larger then the tray but this can be adjusted in the expert settings.

The angle is a measure for how big a piece of cake can fit in. Look in the figure if you don‘t know what to enter here. For example, an angle of 30º is large enough for 1 piece from a 12-piece cake. The length is the length of the piece, which should be about half the diameter of the complete cake. But, be sure to add quite some allowance here.

The most common box. A long, thin, box. The default dimensions are fine for a set of standard, European, playing cards (“bridge size”).

Ir Helovīni, tāpēc pasniedz savus saldumus kā pienākas: ievieto tos zārkā! Ar šo šablonu izveidosi gan kastīti, gan vāku.

Izmanto nedaudz vairāk līmlentes, lai nostiprinātu vāku pie kastītes, citādi zārks varētu naktī atvērties... ļaujiet tā saturam klīst pa māju. Mwhahahaha!

A cone, optionally with the top cut off. (In that case, it’s called a frustum). Can be used to help create the geometry for a beaker, vase, party-hat or lamp shade. If you'd like a real cone, just use zero for the top-diameter. Tip: do not score or fold the fold line this template to keep seam smooth.

Atvērta kaste. Nekam nederīga sūtīšanai pa pastu vai transportēšanai, bet ļoti parocīga dažādu lietu uzglabāšanai un izstādīšanai.

Box with curved sides. The value for curve size can be either positive or negative. You can enter any value, but do not make the curve too large, or the box will break or buckle when folded. Be aware that the Length and the Width do not take the curve size into account.

An elliptical or oval shaped box.

This model can be constructed in the same way as the heart-shaped box and the round box.

The template consists of two parts: a base and a top.

Every part consists of a rim and two pieces for each of the caps. One piece is used on the inside and holds the rim in place. Because this looks ugly, an extra piece is placed on the outside to cover the glue flaps.

Classical letter envelope, most often used for personal letters.

A box consisting of a tray and a lid. The sides of the tray are not glued, but kept together by the lid. Once the lid is removed, the box ‘explodes’ as the sides fall outward.

Gem stone shaped box, consisting of two identical polygonal pyramids, glued together at their bases. It‘s a real box that can used for packaging. It can be stored (and shipped)completely flat. When you pull the two apices (‘tops’) apart, the box will get it‘s full shape. It‘s easiest to glue this shape when both halves are flat. Just fold the glue tabs all the way in and glue the top to the bottom. Just remember not to glue the rounded flaps.

A typical, straight-forward gift box. This box is very similar to the Card Box, but the layout is different. This template makes most efficient use of your sheet of paper if the dimensions are close to eachother. Templatemaker will try to correct impossible values automatically. Be aware of this if, for example, the thumbhole is smaller then you expect.

Heart-shaped box, just because the song by Nirvana is so awesome!

The measurements are different to standard boxes because of the way the heart is modeled: It is made from an ellipse, which is rotated, cut in half vertically and then mirrored.

The Length measures between the two sharp corners of the heart. The Width is calculated by the program to match the rotation (Tilt) and Shape of the ellipse. (Think of the shape as the ”Body Mass Index” of the heart).

The box consists of a base and a lid. Each part has two heart shaped “caps“: the smallest one goes on the inside, the larger one goes on the outside to conceal the ugly-looking glue flaps. It‘s easiest to glue the heart- shaped caps instead of the glue flaps on the rim. The ”Paper Thickness” parameter is only used for making the outside caps larger then the inside.

Īpaši bieza aploksne.

A simple Tray and Sleeve Box. The dimensions are inner dimensions. The clearance is added twice and to both the height and width. The tray can be assembled without glue, although a little glue won‘t hurt, of course.

Piena paka. Ja taisīta mājās, droši vien labāk piemērota sausām lietām, nevis šķidrumiem. Daudz oriģinālāk dāvināt vīnu šādā iesaiņojumā, nevis maisiņā.

Cilindrs, kas sagāzts noteiktā leņķī. To iespējams sagāzt leņķī gan augšpusē, gan apakšpusē. Garums tiek mērīts uz cilindra ass.
Apakšējo leņķi iespējams arī pagriezt ap asi, tā it kā jau sagāztais cilindrs vēl tiktu arī sagriezts.

Sagāztie cilindri vai caurules tiek daudz izmantoti inženierijā cauruļu savienošanā. Tiem, kam patīk šāda veida kastītes, ir dotas arī augšējā un apakšējā šablona daļa.
Esiet uzmanīgi un nelokiet līmes maliņas!

A cone mitered by two planes at a custom angle. These mitering angles must be quite small. If the template looks really weird, check these mitering angles.

(Only circular and elliptical cone-sections are allowed. Parabolic and hyperbolic cross sections are not possible with this template.)

The top- and bottom miter angles lie within the same plane: the “twist“ parameter as present in the mitered cylinder is not (yet) implemented.

How annoying that a sheet the size of an A4 or a Letter is so small, isn‘t it? This template allows you to construct much larger boxes by using 6 separate sheets. It takes a bit more glue but you can make a much more impressive box! Use some sturdy material. You might use scavange some old cereals boxes or pizza boxes. Be aware that your desktop printer might need some ”convincing” to accept these.

A basic tray with glued sides and a draft angle. Use 0º if you want a straight sides, but use a larger value if you want trays that can be stacked into eachother.

The length and width are measured at the top, so when you use a non-zero draft angle, the dimensions at the bottom will be smaller.

Because of the draft angle, the trays can be nested. This makes this model ideal as an organizer for storing small items. LEGO®, for example.

If you choose a too large value for the draft angle or a too small value for the height, the draft angle will be adjusted.

Taisnstūra kastes ir garlaicīgas. Hipsteri rada paralēlskaldņus! Šis šablons rada tīklu jeb paralēlskaldņa papīra modeli - kasti, kura tiek sašķiebta trīs izmēros.

Izvēlieties visu trīs leņķu vērtības starp 0º (pilnīgi plakans) un 90º (taisns leņķis). Atgadinu, ka 100 º leņķis būs ekvivalents 80º leņķim…

Vai vienkāršāk - bilžu rāmītis. Var izmantot arī kā kasti ar dubultajām sieniņām. Šis šablons ir nedaudz sarežģītāks. Rāmīša platumam ir jābūt lielākam par augstumu plus vēl viens centimetrs. Izvēlieties mazāku augstumu relatīvi pret citiem izmēriem.

Piedosim šiem šabloniem nedaudz mīļuma. Liekts kartons - jauki! Atcerieties, ka platumam ir jābūt vismaz divas reizes lielākam par augstumu.

Models of all five so-called Platonic Solids. The Platonic Solids are the five regular convex polyhedra.

The Cube is the most famous one, of course, although he likes to be called “hexahedron” among friends. Also the other platonic solids are named after the number of faces (or hedra) they have. I.e. Tetrahedron, Octahedron, Dodecahedron, Icosahedron. (Now you know how to count in classical Greek, too!)

There is only parameter：the diameter of the midsphere. The midsphere is the sphere from the center of the object that touches all the edges exactly in middle.

Šī ir augstākās klases dāvanu iesaiņošana pašu veidotām dāvanām. Taisnstūra kastes vietā jūs varat izvelēties jebkādu malu skaitu. Izveidojiet trīsstūra, sešstūra vai pat divpadsmitstūra kastīti. Esiet īpaši uzmanīgs salokot vāciņu, ir gan locījumi ar izliekumiem, gan ieliekumiem.

Apmēram aplis.

A pyramid shape with custom height and a regular polygon as base.

Visiem laiku pa laikam vajag apglabāt kādu faraonu. Šādās situācijās noderīga būs piramīda.

Rhombus (lozenge, or lop sided), prismatic box with lid. The box consist of a base and a lid. The dimensions are given for the base. The lid will be scaled with the given percentage (clearance).

A round, cylindrical box.

This model can be constructed in the same way as the heart-shaped box and the elliptical box.

The template consists of two parts: a base and a top.

Every part consists of a rim and two pieces for each of the caps. One piece is used on the inside and holds the rim in place. Because this looks ugly, an extra piece is placed on the outside to cover the glue flaps.

A basic box like, much like the Card Box and the Gift Box. This specific template is very economical for boxes that have small height compared to both the width and the height, for example a box for a tart or a pizza. Templatemaker.nl will try adjust “impossible” values, be aware of this when, for example, the thumb hole or glue flaps have dimensions that you don't expect.

Collection of the 7 concave polycubes with 4 or less cubes. These seven pieces together can form the SOMA cube. That is, if you manage to solve the puzzle. The SOMA cube was invented by the Danish mathematician and poet Piet Hein.

Šablons rada atsevišķu lapu katram segmentam. Kad tos saliek kopā, rodas lode vai globuss.

Star-shape with arbitrary thickness and number of points. The generator will create one spike template for every point of the star. The glue flaps are made double, so you can fold them like this: _/\_ (Think 'namaste'!). If you do now want double glue flaps, choose size '0' for the “Odd Flaps”.

Have you ever dreamed of just sprinkling stars? ✨Now you can, and you can even hide a present in them! The folds are a bit origami-like, score them well and make sure the star is reasonably thick. “5“ Is the ideal number of points, but fewer or more is certainly possible. Shine!

Trapece vai trapeces veida kaste. Ja paralelograms ir pārāk sarežģīts, bet dāvanu kastīte pārāk garlaicīga, trapece ir jūsu ‘izvēles ierocis’

Box insert for thin items. Use this template to create a box insert that locks an item safely in the center of a box. It leaves some extra space for a thumb hole, so it’s easy to retrieve it.